Carter Holt Harvey Shadowclad Prime

Timbakote Timber Pro Rustic for Shadowclad Prime
Timbakote Timber Pro is a water based acrylic stain coating that helps protect CHH Shadowclad Prime ply from the weather and harsh Ultra Violet (UV) rays.

Timbakote Timber Pro is a tough acrylic water based stain coating designed for New Zealand’s harsh conditions, gives excellent adhesion to CHH Shadowclad Prime Ply Sheets while remaining flexible and tough enough to withstand the seasonal movements of timber.

Timbakote Timber Pro is environmentally friendly, non-toxic, non-hazardous, non-flammable and offers 10 year maintained durability on CHH Shadowclad Prime Ply Sheets.

Recommended Uses
Surface Preparation
Drying Times
Clean Up

Visit the Carter Holt Harvey website and
the Climate Surfaces website for more product information.


Timbakote Timber Pro Rustic is an ideal finish for all CHH Shadowclad Prime Ply sheets where a long lasting rustic stain look is required.



Surface should be clean and dry, stains and any stencil marks to be removed. Nail holes and minor defects to be filled with a suitable timber filler, sanded and recoated with Timbakote Rustic Basecoat. All cut edges need to be sealed prior to installation.
If cladding has been left exposed for longer then 30 days,wash down prior to installation with water and a soft broom to remove any contamination. Allow to dry.
Cladding must be coated within 90 days after installation.
LOSP treated ply should be allowed days for solvent treatments to evaporate in the end use situation prior to coating. In periods of cold or wet weather or where ventilation is poor, a longer period maybe required. If in doubt it is recommended to coat a small area and monitor for adhesion and drying.




Stir product well before and during use with a flat stirrer.
Thinning is not generally recommended, as it can be detrimental to the coating performance. The addition of 50mils of water maybe required in hot weather or when coating highly absorbent surfaces.

Apply 2-3 generous coats of Timbakote Timber Pro Rustic with a good quality paintbrush, applicator pad, roller or spray. If spraying, lay off with an applicator pad or brush  to provide an even appearance. Do not over spread. Achieving the correct coating film thickness is important to the life of the coating.


Apply Timbakote Timber Pro Rustic to one sheet at a time, lay off in long even strokes along the sheets length working to natural breaks. Always keep a wet edge to avoid lap marking. Highly exposed areas will require an additional coat for extra protection due to extreme weathering. Apply the final coat of Timbakote Timber Pro Rustic after the cladding has been fixed to the wall. Pay particular attention to the coating of the grooves.

Use colours with a light reflectance value of 40% or more to meet the 50 year durability requirement of the NZBC. 

If precoating Shadowclad Prime prior to installation do not allow the sheets to be stacked together without plastic film between the layers.


6 – 12 sqm per Litre


Depending on such factors as film thickness, ambient air temperatures, humidity levels and air circulation.

The general dry times at 6-12 sq metres per Litre are:
Touch Dry 20 minutes
Re-Coat Time 2 hours
Curing Time 7 days 


Recoating should take place before deterioration of the coating allows weathering of the timber substrate to take place. A patchy, thin, faded and uneven appearance or eroded coating on edges indicates the need for recoating.
A wash down on an annual basis with a slow release moss and mould wash will help with the long-term maintenance of your coating.


All equipment can be cleaned up in water.


TKote-Rustic-Coatings-72.jpg Wear impervious gloves and wash paint deposits off skin with soap and water.

Moderately irritating to eyes- wear splash proof goggles to protect eyes. Flush eyes immediately with plenty of water if coating splashes to the eyes occur. If discomfort persists seek medical attention.

Keep out of children’s reach. Ingestion; Give 1-3 cups of water and seek medical attention.


Let residual coating dry by leaving the lid off the container. Dispose with refuse if permitted by local council. Paint containers are reusable for non-food purposes and recyclable in areas where recycling and collection facilities are available.


Timbakote’s 10 year maintained durability statement on CHH Shadowclad Prime. If the Timber Pro Rustic system is applied correctly on properly prepared CHH Shadowclad Prime as per the label instructions it will not crack, peel or blister providing the recommended maintenance procedures are carried out and the substrate remains stable.
Any failure of the substrate or previous coating is not covered. If this protective coating fails to perform as specified Timbakote Coatings Ltd will provide free of charge sufficient product to recoat the affected area. In addition to this you may have other remedies at law.
Every care is taken to ensure that the information provided in this data sheet is accurate. Timbakote Coatings Ltd is unable to guarantee results as it has no control over the conditions under which products are applied, the substrate or the applications.  The Customer has to determine the suitability of the delivered products or information for its intended purpose.
About our company
Enter a succinct description of your company here
Contact Us
Enter your company contact details here